Scroll to Top

Serpent Syder 2wd SCT 1/10 scale, electric powered Short Course Truck , rear motor

High performance race geometry
Very long wishbones
Unique  steeringblock  design
Big bore 12mm RCM type shocks with dual system
Highly Efficient Steering ackermann
Wide side guards with polycarbonate inserts
Rear motor design
Adjustable rear differential height
3 pad slipper clutch / ball differential
Narrow composite Chassis design
Light SC body with flares

Serpent Main Site


INTRODUCTION:

Serpent designer Billy Easton, former 1/10 scale 2wd World Champion, and the designer of the successful Cobra 1/8 series of cars and the recent Spyder 2wd buggy in RM and MM, has created this next masterpiece, the rear motor SCT version of the very popular Spyder series .  

Serpent decided to create the Short Course Truck based on the very popular Spyder rear motor buggy.

INTERVIEW:

An interview on the Serpent Spyder SRX2SC Project with Serpent designer and toplevel racer Billy Easton, USA.
READ FULL INTERVIEW


Serpent Spyder SRX-2 SC
Build Gallery Video

Click image to play video

   

CHASSIS:

Composite chassis plate with a layout allowing for a perfect weight balance, and optimal space for the electronics, battery and servo.  The front Kick-up angle in the Chassis incorporates more clearance for racing and allow for more nose landings.

SHOCK ABSORBERS:

Dual system 12mm big bore shocks with hard coated threaded bodies, a unique cap design, a superbly sealing o-ring and spacer package. The Shocks can be used in Bladder or Emulsion setups. The shock-set comes with a set of moulded pistons to choose from.  A selection of 5 springs-sets is available to fine-tune the suspension settings.  Shock Collars with inner o-rings are used on the threaded bodies to set-ride height.

FRONT UPPER BULKHEAD:

The front upper bulkhead supports the upper links and shock tower in the best possible way. The front section offers the option to mount a front sway bar unit

FRONT WISHBONES:

The long front Wishbones are made from a super strong composite material. The arms are angled to optimize the CG and pivot on 3mm captured pins on the inside and out. The arms have 2 mounting positions for shock angle and are prepared to use an optional anti-roll bar if needed.

 

FRONT AND REAR TRACK ROD ENDS:

Spring steel front and rear track rods are mounted to durable composite captured ball joints.  The track Rods have L/R threading for easy adjustments.

STEERING SYSTEM AND ACKERMANN:

The steering system has a reverse swinging pivot system that optimizes the efficiency through all different types of corners. You have 3 Ackerman choices to choose from.

STEERING BLOCKS:

The steering blocks fit 5x10x4 mm bearings. The steering blocks utilize some of the best high strength materials on the market today.

DIFFERENTIAL:

The limited slip ball differential is a super compact, effective and durable unit. Utilizing 1/8th inch diff balls for ultimate durability. The structure and assembly is common type in this class, but the high quality parts and well functioning will make it stand out.  The height of the diff can be changed with inserts.

SLIPPER CLUTCH:

The Serpent slipper  is a super compact and narrow design. The 3 pads are a special type of material of which the temperature is very stabile, so the feel and performance of the slipper remains the same throughout your run. The slipper is easily accessible from the opposite side, so no need to remove any sidecover. 

REAR UPRIGHTS:

The rear hub uprights use a larger 5x14x4 outer bearing and 10x15x4 mm inner for ultimate lasting performance. The rear uprights utilize some of the best high strength materials on the market today.

The rear uprights allow you to adjust, the toe in from -2 to + 2 degrees by use of various inserts also included in the kit. (image shows also optional alu versions)

WHEEL AXLES AND WHEEL HEX: 

The spring steel wheel-axles utilized 12mm hex adapter to follow current market standards. The front springs steel axle is fixed, while the rear wheel-hex is a clamping aluminium version.

 



BATTERY SPACE MOUNT AND WEIGHT BALANCE:

The battery is mounted perfectly in the centre line of the car. It’s an exact fit for saddle packs. In case of using a Shorty-pack, it can be moved to front or back to play with weight balance. Pieces of hard foam are supplied to do so and secure the battery in position. The carbon fibre battery-top-brace has a secure quick release system with handy alu twist nuts.

ANTI-ROLL BARS:

Anti-roll bars can be fitted on the front and rear of the car, but are optional. They can be used on high grip surfaces to further adjust the cars performance


 

CASTOR BLOCK AND SETTINGS: 

Caster block inserts come as 0, 2.5 and 5 degree version all of which are included.  The caster blocks are very compact and strong units made from a special composite material.

 

MOTOR PLATE AND MOTOR GUARD:

The motor plate comes in black anodized aluminium.

REAR TRANSMISSION CASE:

The composite rear transmission case is light and durable. It allows the driver to adjust the differential height to each specific condition. It also securely holds the motor plate, differential as well as supports the rear wing mount.

REAR CHASSIS SKID PLATE: 

The composite rear skid plate connects to the chassis plate. This connection allows you to unclip the rear end in one piece, but helps reduce the total cost of maintenance. It is also made from extremely high strength composite material.

REAR SUSPENSION BRACKETS AND TOE IN:

The 3mm spring steel pivot pins are held in place by the suspension bracket made from aluminium.  Inside the bracket you use inserts to set toe-in and roll centre. You can adjust the toe-in from 2 to 4 degrees and adjust the anti squat from 0 to 4 degrees.

 

REAR SUSPENSION ARMS:

The long and durable angled rear suspension arms are very tough units to withstand the rigors of the track and the hard landings.  The rear arm offers 2 options for shock position and two mounting locations for the rear anti-roll bar if needed.

REAR DRIVESHAFT SYSTEM, WHEEL AXLES: 

The spring steel drive shafts are thin and light, yet durable.  The spring steel wheel-axles are 5mm, light and durable, guided by the 2 different sizes of bearings, inner 10x14x4 mm and outer 5x13x4 mm. The driveshaft pin is fully captured to prevent any failure. These bearings are for sure to stand up the rigors of any track condition.

BODYSHELL AND FLARES: 

The light realistic looking Short Course style body, made in top quality clear polycarbonate, has a nice flowing line, steep front windscreen for down force.  The separate flares in the rear section help for stability in jumps, high speed and cornering.

FRONT AND REAR BUMPER SYSTEMS: 

The durable composite front bumper system will absorb the worst of head on crashes and will allow for safe nose landing. The rear bumper section is a very durable unit, easy to disassemble, and fits well with the rear of the body, to absorb the worst of back-end crashes.

FRONT AND REAR SHOCK TOWERS:

Durable composite front and rear shock towers, with multiple shock angle positions allowing drivers to fine tune for varying track conditions.

SIDE GUARDS:

The side-guards or nerf-bars are an innovative construction. The sideguards are made wide, so it supports the sides of the body well. The inside of the guards are open, but filled with polycarbonate sheets.  In jumps with SC cars you have the ballooning effect, as wind is captured under the body, losing stability.  The closed section on the Serpent Spyder SC will largely prevent that from happening, creating better balanced jumping and more stability.  The pre-cut polycarbonate sheets come clear and can be painted in your favourite colour scheme too!


BALLBEARINGS:

High speed sealed stainless steel ballbearings with aeroshell oil

FASTNERS:

Hard steel , mostly allen screws, roundhead and countersunk.  Minimized number of different allen heads to make working on the car easier.

 



WHEELS: 

Durable white Serpent Short Course wheels.

 

INCLUDED:

The kit comes complete with body and wheels, full colour manual and exploded views, a blank and standard set-up sheet and Serpent decals.

Racing chassis
Clear body  and rear wing
Front and rear wheels with 12mm hex
Full colour manual and decals
Not included: tyres/inserts/electronics


SET-UP POSSIBILITIES:

Wheelbase
Caster
Ackerman
Axle height Front
Front and rear camber
Front Toe-in and toe-out
Rear Inboard toe-in angle
Rear Outboard toe-in angle
Antisquat
Roll-centers
Ride height
Weight balance
Shocks for dampening and springs, shock angle
Gear ratios
Anti-roll bar thickness (  option)
Electronic placement

TECH-SPECS:

Length540mm (with body)
Width: 295mm (varies with set-up)
Height: 190mm
Wheelbase: 330mm
Gear Ratio: 2.43:1 
Weight: varies with electronics used

Designed by Billy Easton, USA

 

OPTION PARTS: Details to follow soon and much more to come..

 
 

 

   
 
   

 

 
   

Dragon-RC Novarossi